Jandy CC Series: A Drop-In Replacement for Pentair Clean & Clear Plus

Replace the filter. Keep the plumbing plan.

When a filter needs replacing, one of the first questions is what else has to change around it. A different connection layout can turn a straightforward equipment swap into a larger conversation about pipe runs, fittings, and space.

Jandy designed the CC Series specifically around the Clean & Clear Plus replacement. According to Jandy, compatible installations can be replaced without replumbing. That is the practical appeal: a path to a new filter that starts with the layout already on your pad.

For a pool owner, that makes the CC Series worth asking about before automatically ordering the same filter again. For an installer, it puts connection compatibility at the center of the equipment selection.

What makes the CC Series a purpose-built drop-in?

The replacement design goes beyond a similar-looking tank. Fluidra's product guide highlights the details that connect the new filter to the existing installation:

• Matching inlet and outlet positions. The comparison drawing shows 7.5-inch port spacing on both filter families, with the lower port center 8.1 inches above the base.
• Pentair-style unions included. The supplied connections are part of the replacement design, rather than an afterthought when planning the swap.
• Handles for easier service. Integrated handles provide grip when the top needs to be removed during professional maintenance.
• Material built for the equipment pad. Fluidra highlights corrosion-free, UV-resistant tank material.

Those details make the drop-in story concrete: familiar connection positions, included unions, and features designed for ongoing care.

Which Jandy CC replaces your Clean & Clear Plus?

The lineup includes the CC300 (300 sq. ft.), CC400 (400 sq. ft.), and CC500 (500 sq. ft.), each with four cartridges. Start with the complete model number on your current tank, then use our sizing guide.

Jandy's manual identifies the starting pairings: CCP320 to CC300, CCP420 to CC400, and CCP520 to CC500. The larger-model options above reflect ePoolSupply's sizing expertise. “Go up, not down” means moving up from the corresponding CC model—not comparing the numbers in the Pentair and Jandy model names. This guide concerns complete filters, not interchangeable cartridges.

Take a photo of the tank label before comparing options. “Clean & Clear” and “Clean & Clear Plus” are separate product names. The full name and model number help keep the discussion focused on the correct equipment.

What should you check before a drop-in replacement?

The best replacement conversation starts with your actual pad. Bring the label photo and a few wider photos showing the filter, pipe connections, and nearby equipment.

• Confirm the model. Identify the corresponding CC replacement, then choose that model or a larger CC model using ePoolSupply's sizing guide.
• Check the surrounding space. Plan around the CC Series footprint of 26.5 inches wide by 24 inches deep. The manufacturer guide specifies 6 inches minimum side clearance; your installer should also confirm access for service.
• Review the existing connections. Have the professional assess their condition and alignment before planning the swap.
• Plan for future service. Leave the access needed to open, inspect, and maintain the filter.
• Review the whole system. Ask the installer to confirm filter selection and operating flow for your pump, plumbing, and pool.

A useful question to ask is: “Can this CC Series model use my existing connections, and is there enough room to service it?” That turns a broad compatibility claim into a decision based on your installation.

Know the footprint before you plan the swap

Fluidra's replacement guide lists these tank heights for the starting replacement pairings. All three Jandy CC models share the 26.5-by-24-inch footprint.

Dimensions are from Fluidra's 2027 product replacement guide. Minimum side clearance is 6 inches. Tank height is not the required overhead service clearance; have the installer check room for lid and cartridge removal. If you size up, plan around the dimensions of the CC model you actually choose.

Beyond the fit: what else does the CC Series offer?

Lower head loss under manufacturer test conditions

Fluidra reports up to 50% lower head loss versus Pentair Clean & Clear Plus, based on internal testing across 60–150 GPM.

Head loss is resistance to water moving through the filter. Compare performance at the flow your pool needs; this test result does not mean a matching reduction in electricity costs. Actual performance depends on the pump, plumbing, layout, and settings.

Cartridge filtration with straightforward upkeep

Jandy highlights a clean/dirty indicator, accessible service components, and longer intervals between cleanings. Ask your pool professional to explain the service routine and what to watch for on your particular system.

Keep the starting pressure and cleaning dates with your pool records. Those details give you and your service professional a useful reference as the filter operates.

Questions pool owners ask